If you’re still having trouble opening your gun cabinet, you can always contact a locksmith. Be careful when doing this so that you don’t damage any of the guns inside! Then, reach in and unlock the door from the inside. Drill a hole in the back of the cabinet big enough for your hand to fit through. This may take some time and patience, but it is definitely possible.Īnother way is to use a drill. One way is to use a paperclip or other thin object to pick the lock. If you have a gun cabinet that uses a key to open, but you don’t have the key, don’t worry! There are a few ways that you can open the cabinet without the key. See also What Size Drill Bit for 1/2 Inch Dowel How to Open Stack on Gun Cabinet Without Key With this piece removed,the cylinder will be free to turn and unlock the door. Once the drilling is complete, use a screwdriver or other tool to push out the drilled-out piece of metal from inside the lock cylinder. Be careful not to drill too deeply or you may damage the inside of the gun cabinet. Next, using a drill bit that is slightly larger than the diameter of the locking pin, drill through the center of the locking pin. Once the screws are removed, the lock should come right off. There are usually two screws, one on each side of the lock. If you have a Stack-On gun cabinet with a locked door, and you need to drill out the lock, here’s what you need to do.įirst, remove the screws that hold the lock in place. Be careful not cause any further damage in this process! How to Drill Out a Lock on a Stack-On Gun Cabinet Gently wiggle or twist until you feel resistance give way – once that happens, carefully pull open the door of your safe. To do this, insert a rod or piece of wire into the newly-drilled hole until it hits something solid (this is likely the backplate of the locking mechanism). Now it’s time for the next step: actually opening up the door of your safe. Once you’ve drilled through the entire keyhole, stop and take a break – this process can be physically tiring! Apply steady pressure as you work if the drill gets stuck, try using more lubricant or switching to a larger drill bit. When you’re ready, begin drilling into the center of the keyhole on your safe’s door. This will minimize damage and make it easier to patch up afterwards if needed. If possible, start with the smallest drill bit that will still be able to penetrate the material of your safe. Begin by attaching the drill bit to your power drill. Once you have your supplies, it’s time to get started. In terms of safety gear, it’s always a good idea to wear gloves and eye protection while working with power tools. You’ll need a power drill, a drill bit that’s appropriate for the material of your safe (typically metal), and some sort of lubricant. The first step is to gather your supplies. Keep reading to learn everything you need to know about drilling out a safe lock. This process can be done relatively easily with the right tools and a little bit of know-how. If you’re wondering how to drill out a safe lock, you’ve come to the right place. 5, Continue drilling until you have drilled through the entire lock cylinder How to Drill Out a Safe Lock.Apply pressure to the trigger and slowly start drilling into the lock cylinder. ![]() Place the tip of the drill bit on the center of the lock cylinder.Insert the drill bit into the drill and tighten.Purchase a drill bit that is the same size as the lock cylinder.This can be a difficult task, but it is possible with the right tools and some patience. Please click here for more information.If you have a gun cabinet with a lock that is no longer working, you will need to drill out the lock in order to gain access to the contents of the cabinet. Please note: Orders of 151-pounds or more will be shipped via Freight carrier and our Oversized Item Delivery/Return policy will apply. Internal dimensions: 54.88 inches high x 15.63 inches wide x 12 inches deep.Exterior dimensions: 55-1/8 inches high x 15-7/8 inches wide x 15-1/8 inches deep.Batteries are accessible from the front of the safe and are easy to replace.Approved by the California Department of Justice.These security safes include Stack-On's patented gun barrel rests and standoffs for scoped guns and a flush mount bottom for easier attachment to the floor. Stack-On Full Sized Gun Security Safes with Fully Carpeted Interior are DOJ-approved, Include Large, Live Action Locking Bolts, Solid Steel Dead Bolts on the Hinge Side of the Door of Full-Length Safes.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |